■ Silicon Nitirde Ceramic Stalk
■ Riser Tube & Stalk For Aluminum Low Pressure Die Casting
■ Low Pressure Die Casting Machine Parts
■ Riser Tube & Stalk 120x100x642 Mm (With Gasket And Metal Flange)
■ Riser Tube & Stalk 170 X150x600 Mm (With Gasket And Metal Flange)
■ Riser Tube & Stalk 150x130x562 Mm (With Gasket And Metal Flange)
■ Alutit T Riser Tube 100 X 60 X 900 Mm，100 X 70 X 800 Mm
■ Aluminium Titante Riser Tube 70x100x930 Mm
■ Ceramic Riser Tube 140x110x850 Mm For Industrial Furnace
■ Riser Tube 580x110/80x40 Ceramic Tube For Dosing And Feeding Liquid Aluminum From A Dosing Furnace
■ Thermocouple With Protection Tube Assembly
■ Industrial Process Control System,Temperature Element, Type K Thermocouple, Protection Tube
Riser tube & Stalk is the key part of the low pressure casting machine for casting aluminum alloy products(such as aluminum wheels,other aluminum alloy products), In die casting process ,molten aluminum(700-900)is sent from riser tube to mould cavity evert 3-5 minutes . Ruihong's silicon nitride riser tubes have excellent corrosion resistance, low thermal-expansion coefficient ,its service life is 5-20 times longer than usual material , after using ,it can improve the quality of aluminum alloy products,Significantly reduce labor maintenance costs and increase profits for you.
■ Sialon,silicon nitride,alumina and silicon carbide are known as engineering ceramics. Among them, silicon nitride has the highest thermal shock resistance. Thus, it makes handling and preheating control easier.
■ Low wettability against molten aluminum makes material adhesion on tube less and it makes daily maintenance easier.
■ Superior corrosion resistance does not allow eluted contamination into molten metal. This is a key factor to maintain purity of molten alloys.
■ Silicon nitride is a dense material and maintains its high mechanical strength even at elevated temperatures.Compared to reaction bonded materials, it assures trouble free operation. In fact, practical accomplishment shows more than 1 year in use.
1. Assembly
When riser tube & stalk is connected with the furnace and the mold, the seal should be tight. The tightness of the gas seal gap and the selection of sealing materials are very important. When it is too tight, the pressure is large, the force is easy to fracture for a long time, and the gas will leak in a short time when it is too loose. In addition, the selection of the sealing pressing part should be reasonable to avoid the displacement of the stalk's flange force and shorten the service life. To grasp the gap, materials, installation methods and other links gradually accumulate experience.
2. Preparation before use
The stalk should be fully preheated before entering the furnace. If it is heated with a gas torch, it should be slowly and evenly inside and outside to avoid local excessive heating. When the temperature reaches 600°C, the tank will turn dark red, and the time will be about 30 minutes. You can also put the stalk in the furnace, so that the bottom of the stalk is about 2 centimeters away from the aluminum liquid surface, and wait for the wall of the stalk to be all red (about 30 minutes), you can slowly put into the molten aluminum. This operation can not only dry the moisture in the stalk, but also avoid the explosion caused by sudden temperature rise of the stalk.
3. Pay attention in use
When using the stalk, we must pay attention to reduce the knock on the pipe mouth, especially after plugging aluminum can not be hard hit. When replacing the mold and repairing the equipment, the impact vibration should be reduced as much as possible, and the exposed parts of the stalk should be kept warm to prevent acute cooling. When slagging, pay attention not to directly collide with the stalk, and when adding molten aluminum, pay attention to avoid directly pouring on the body of stalk.
4. Furnace maintenance
When the furnace shutdown maintenance equipment must take the stalk out of the oven, do not put the hot stalk directly on the ground, should be wrapped with refractory materials and placed in a place that is not directly blown by cold wind.
YIWU RUIHONG PARTS COMPANY
Industrial Zone,Huzhou\Ningbo,Zhejiang,China
(86）572-2373192 (86) 18006626989